manualshive.com logo in svg

Keysight N9923A, Руководство пользователя, Страница: 232 / 276

Поделиться
Скачать
Keysight N9923A Скачать руководство пользователя страница 232

 232                                                                                                                     Keysight N9923-90001 User’s Guide

System Settings
Power ON

—

DHCP

 - IP Address is assigned dynamically. If your server supports this 

feature, the IP Address for the FieldFox is assigned each time it is 

started. 

—

Static

 - Set the IP Address manually. The Address remains until you 

change it.

—

Static IP Address

 - Enter the IP Address – including periods - in the format 

nnn.nnn.nnn.nnn

—

Static Subnet Mask

 - Enter the Subnet Mask – including periods - in the 

format nnn.nnn.nnn.nnn

—

Static Gateway

 - Enter the Static Gateway – including periods - in the 

format nnn.nnn.nnn.nnn

—

Apply Settings

 Choose from:

—

Power Up

 The above settings take effect when the FieldFox is started.

—

Now

 The above settings take effect immediately.

— Press 

Done Edit

 when finished.

Power ON

When the FieldFox is without a power source, this setting allows the FieldFox 
to power ON as soon as a charged battery or the DC Adapter is inserted 

without pressing the power button. 

How to set Power ON

— Press 

System 7

.

— Then 

System Configuration

.

— Then 

Power ON

.

— Then choose from the following:

—

Auto

 The FieldFox will power ON when a charged battery or the DC 

Adapter is inserted.

—

Manual

 The FieldFox will power ON only when the power button is 

pressed.

To make the LAN settings persist after power up, toggle Apply Settings to 

Now then back to Power Up. You should see a message indicating that the 

LAN config file was saved.

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов