Keysight N9923A Скачать руководство пользователя страница 142

Страница: 142 / 276

142 Keysight N9923-90001 User’s Guide

Frequency Offset Using Power Sensor (FOPS) – Option 208
FOPS Settings

Rx = 5.8 GHz to 6.8 GHz

Power Sensor Settling

The following two settings work together to allow you to choose the right

compromise between measurement speed and accuracy.

Each power sensor reading is considered “settled” when either:

— The difference between two consecutive readings are within the Tolerance

value.

—

the Max (number of) Readings has been made.

The readings that were taken are averaged together to become the displayed
reading.

How to choose Power Sensor settling

— Press

BW 2

— Then

Tolerance

. Enter a value in dB between 0 and 10 using the numeric

keypad, the

arrows, or the rotary knob. Tolerance of 0 will never be

achieved, so the Max Readings will always be made. Press

Enter

— Then

Max Readings

. Enter a value between 1 and 20 using the numeric

keypad, the

arrows, or the rotary knob. Press

Enter

Sweep Settings

These settings provide added control of the FOPS measurement.

How to make additional sweep settings

— Press

Sweep 3

— Then choose from the following:

—

Power Setup

—

Source Enable

——

Turn ON the internal source (required for FOPS).

——

OFF

Turn OFF the internal source

—

Src Nom Power

(-15 dBm default setting) Set output power to an

arbitrary value at the source CW frequency. Then enter a value using
the numeric keypad, the

arrows, or the rotary knob. Press

Enter

—

Num Points

Freq Step Size

Both settings control the number of power

sensor measurements between the Start and Stop frequencies. Enter one

setting and the other will be changed automatically. There must be at least
two data points.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 142 / 276

Результаты поиска

Содержание N9923A

Отзывы: