Keysight N9923A Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 276

Keysight N9923A Скачать руководство пользователя страница 58

58 Keysight N9923-90001 User’s Guide

NA (Network Analyzer) Mode
NA Mode Settings

Notes:

— To move a marker, press

Marker

, then

Marker

, then scroll to the marker

number to be moved. The new marker position can NOT be saved with the A
or B display state.

— Settings that are NOT listed above are NOT affected by the recalled display

states.

— Changes to the above settings outside the Big Readout menu will be

overwritten when Big Readout (A or B) is selected. For example, suppose
the display format for the B state is Log. If you change the display format to

Lin using the standard menu (Meas 1, Format), the setting will show on the
display. But if you then use the Big Readout (A | B | OFF) setting, when B is
recalled, the Lin setting will be overwritten with the original Log setting.

Increase Dynamic Range

Dynamic range is the difference between maximum input power to the
FieldFox receiver (without compressing the receiver), and the minimum
measurable power (noise floor). Measurement accuracy is increased when the

DUT response is at least 10 dB above the noise floor. For a measurement to be
valid, input signals must be within these boundaries.

The following settings will increase the dynamic range of your NA mode
measurement.

— Increase Power Level: Press

Meas 4

then

Output Power High

— Lower the IFBW: Press

BW 2

then

IF BW

— Increase Averaging: Press

BW 2

then

Average

The following procedure MAY increase the dynamic range of your NA mode
measurement. The results you see will depend on the performance of your
DUT.

With an S21 trace active:

1.

With RF OUT (port-2) open, press

Trace 6

then

Math and Memory

then

Data->Mem

«
...
56
57
58
59
60
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов