Keysight N9923A Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 276

Keysight N9923A Скачать руководство пользователя страница 141

Keysight N9923-90001 User’s Guide 141

Frequency Offset Using Power Sensor (FOPS) – Option 208
FOPS Settings

——

Start

Annotated as Start and Stop frequencies.

——

Center

Annotated as Center and Span frequencies.

——Then choose from the following two methods to determine the

offset frequency

(the frequency that the receiver is offset from

the source). This is typically the frequency of the LO that is
used with the frequency converter. The frequency offset may
be positive, negative, or zero.

——

Freq Offset

Enter an Offset frequency. The receiver frequencies

are calculated.

——

Offset Calculator

Enter the Receiver Start and Stop

frequencies. Then press

Calculate Offset

.

——Press

Rx Sweep

to select the receiver sweep direction.

——

Fwd

Used for systems for which the output frequency is

Offs + Src. The output frequency of the DUT and the

receiver sweeps in the same direction as the source.

——

Rev

Used for systems for which the output frequency is

Offs - Src. The output frequency of the DUT and the

receiver sweeps in reverse direction as compared to the
source.

Invalid Settings

Violations of the following conditions will return an error message:

— The frequency span for the source and receiver must be the same.

— Both the source and receiver frequencies must be positive.

FOPS Configuration Examples

Negative Offset, RxSwp =

Fwd

(Offs + Src)

Src = 2 GHz to 3 GHz

Offset = -1 GHz

Rx = 1 GHz to 2 GHz

Positive Offset, RxSwp =

Rev

(Offs - Src)

Src = 2 GHz to 3 GHz

Offset = 3.8 GHz

Rx = 1.800 GHz to 800 MHz

Positive Offset, RxSwp =

Fwd

(Offs + Src)

Src = 2 GHz to 3 GHz

Offset = 3.8 GHz

«
...
139
140
141
142
143
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов