Keysight N9923A Скачать руководство пользователя страница 73

Страница: 73 / 276

Keysight N9923-90001 User’s Guide

Time Domain – Option 010
Gating

Trace 4 shows the

frequency

response

with

gating enabled.

How to make Time Domain Gating settings

— Press

Measure Setup 4

— Then

Transform

— Then

Gating

— Then choose from:

—

Gating is being performed.

—

Off

Gating is NOT being performed.

Start, Stop, Center, and Span Gate Times

These settings specify the time in the trace to be gated (in or out). The gate
times can be specified using either Start and Stop or Center and Span.

— Press

Gating Start Stop

— A settings table appears that allows you to navigate and select the

following settings. These settings are made exactly like those made on the
Transform Settings table. Learn how in

“Transform Settings Table” on

page 64

Gating Type

This setting defines the type of filtering that will be performed for the gating
function. The gate start and stop flags on the display point toward the part of

the trace you want to keep.

Choose from the following:

—

Bandpass

KEEPS the responses within the Gating Start and Stop times.

—

Notch

REMOVES the responses within the Gating Start and Stop times.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 73 / 276

Результаты поиска

Содержание N9923A

Отзывы: