Keysight N9923A Скачать руководство пользователя страница 87

Страница: 87 / 276

Keysight N9923-90001 User’s Guide

CAT (Cable and Antenna Test) Mode
1-Port Cable Loss Measurements

A 2-port Insertion Loss measurement is usually more accurate than a 1-port
Cable Loss measurement. However, to perform a 2-port Insertion Loss

measurement, both ends of the cable must be connected to the FieldFox.

How to make a 1-port Cable Loss Measurement

Press

Preset

then

Preset

Then

More

then

Cable Loss (1-Port)

Connect the cable to be tested.

Press

Freq/Dist

and enter

Start

and

Stop

frequency values of the

measurement.

Press

Sweep 3

then

Min Swp Time

. Increase the Sweep Time until a stable

trace is visible on the screen. The amount of time that is required increases

with longer cable lengths. Learn more in the

Supplemental Online Help

http://na.support.keysight.com/fieldfox/help/SupHelp/FieldFox.htm

Remove the cable to be tested.

Press

Cal 5

, then

QuickCal

Mechanical Cal

. Mechanical Cal.

Follow the prompts to perform calibration at the end of the jumper cable

or adapter. Learn more about Calibration in

“How to Perform a

Calibration” on page 104

Connect the cable to be tested.

10.

Connect a LOAD at the end of the cable to be tested. This limits the

reflections to faults that are located in the cable under test.

11.

Press

Trace 6

then

Data->Mem

to store the trace into Memory.

12.

Remove the LOAD and leave the end of the cable to be tested open.

13.

Press

Data Math

then

Data – Mem

. The ripple in the measurement is

removed. These minor imperfections in the cable should not be considered

in the Cable Loss measurement.

In high-loss conditions, a Cable Loss measurement becomes ‘noisy’ as the

test signal becomes indistinguishable in the FieldFox noise floor. This can

occur when measuring a very long cable and using relatively high

measurement frequencies. To help with this condition, use High Power

and Averaging.

Low-level standing waves (also known as ‘ripple’) which may be visible in

reflection measurements, can hide the actual loss of the cable. Steps 10

through 13 can minimize the ripple. Perform the measurement with and

without steps 10 through 13 and choose the method with the least amount

of ripple.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 87 / 276

Результаты поиска

Содержание N9923A

Отзывы: