Keysight N9923A Скачать руководство пользователя страница 3

Страница: 3 / 276

Where to Find the Latest Information

Documentation is updated periodically. For the latest information about these products, including instrument

software upgrades, application information, and product information, browse to one of the following URLs,

according to the name of your product:

http://www.keysight.com/find/fieldfox

To receive the latest updates by email, subscribe to Keysight Email Updates at the following URL:

http://www.keysight.com/find/MyKeysight

Information on preventing instrument damage can be found at:

www.keysight.com/find/PreventingInstrumentRepair

Is your product software up-to-date?

Periodically, Keysight releases software updates to fix known defects and incorporate product enhancements.

To search for software updates for your product, go to the Keysight Technical Support website at:

http://www.keysight.com/find/fieldfoxsupport

A.08.15 Firmware Release Updates (N991xA/2xA/3xA with serial

number prefixes <5607 Only)

For customers upgrading FieldFox firmware, the following is a list of changes from the previous release:

File Management:

“Manage Files” on page 199

“Manage Folders” on page 200

A.09.50 Firmware Release Updates (Also, applies to N9923A units

with serial number prefixes

≥

5607)

For customers upgrading FieldFox firmware, the following is a list of changes from the previous release:

Added Real-Time Spectrum Analysis (RTSA) Mode (

Option 350 does not apply to N9923A

)

Added miscellaneous updates.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 3 / 276

Результаты поиска

Содержание N9923A

Отзывы: