Keysight N9923A Скачать руководство пользователя страница 47

Страница: 47 / 276

Keysight N9923-90001 User’s Guide

NA (Network Analyzer) Mode
NA Mode Settings

—

Smith

Used mainly for S11 and S22, which are plotted on a Smith

Chart. Displays series resistance and reactance.

—

More

then…

—

Polar

Used mainly for S11 and S22. Displays magnitude and phase

of the reflection coefficient.

—

Group Delay

Used mainly for S21 and S12. Displays signal

transmission (propagation) time through a device in seconds. The

Group Delay aperture is the current Smoothing aperture. Default is
1.5% of the X-axis.

——Learn how to set Smoothing aperture on

“Smoothing” on

page 51

——Learn more about Group Delay measurements at the FieldFox

Supplemental Online Help:

http://na.support.keysight.com/fieldfox/help/SupHelp/FieldF

ox.htm

—

Unwrap Phase

Same as Phase, but without 180 degree wrapping.

Frequency Range

Set the range of frequencies over which you would like to make measurements.

When the frequency range is changed after a calibration is performed, the cal
becomes interpolated. Learn more in

“Interpolation *” on page 119

How to set Frequency Range

This can be done in two ways:

— Press

Freq/Dist

— Then choose from the following:

—

Start

and

Stop

frequencies – Specify the beginning and end of the

sweep.

—

Center

and

Span

frequencies - Specify the center frequency and

span of frequencies (half on either side of center).

Phase is unwrapped by comparing the phase from one data point to the

next. If the phase difference between two data points is greater than 180

degrees, or if the phase of the first data point is greater than 180 degrees

from DC, than the phase measurement is probably NOT accurate. To

ensure that the phase measurement is accurate, increase the resolution

setting. When making a narrow band measurement, reduce the start

frequency for the unwrapped phase measurement to ensure the first data

point is less than 180 degrees from DC.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 47 / 276

Результаты поиска

Содержание N9923A

Отзывы: