Keysight N9923A Скачать руководство пользователя страница 224

Страница: 224 / 276

224 Keysight N9923-90001 User’s Guide

System Settings
System Configuration

Figure 14-1

GPS Display

— The left portion of the screen displays satellites and the corresponding

number on the adjacent Satellite Power chart.

— The right portion of the screen displays Satellite Power Carrier to Noise

(C/No) dBHz values on the tops of the satellite power chart.

GPS Status

With GPS enabled the following is displayed at the top of the FieldFox screen:

The following icons (located in RED circle above) indicate the GPS lock status:

- GPS ON and locked on satellites.

- GPS ON, but NOT locked on satellites.

- GPS ON, but no GPS receiver is present or detected.

The following annotation (BLUE circle in above image) indicates the

INTERNAL

top-panel antenna status:

— Ant:

INIT

– antenna status initializing.

The C/No values returned are not calibrated at the factory or warranted for

accuracy. The numbers retrieved are passed unprocessed directly from the

GPS receiver in use.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 224 / 276

Результаты поиска

Содержание N9923A

Отзывы: