manualshive.com logo in svg

Keysight N9923A, Руководство пользователя, Страница: 24 / 276

Поделиться
Скачать
Keysight N9923A Скачать руководство пользователя страница 24

 24                                                                                                                     Keysight N9923-90001 User’s Guide

Preparing for Initial Use of Your New FieldFox
FieldFox High Temperature Protection

— To turn Power 

OFF

 (very low battery drain), press and hold the power 

button. Data and instrument state are NOT automatically saved when the 

FieldFox is powered OFF. Learn how to save data and instrument state in 

Chapter 13, “File Management”, on page  191

. See the Note above 

concerning Shut down.

— To restart FieldFox, press the power button and press 

Restart

. See the 

Note

 

above concerning Restart.

— Press 

Cancel

 to exit the power down sequence.

— You can also access the power down softkey menu choices (

Standby

, 

Shut 

down

, 

Restart

, and 

Cancel

) by using the 

Mode

 hardkey:

— Press 

Mode

—Then 

More

—Then 

Shut down

— You can make a setting to automatically 

Power ON

 the FieldFox when a 

power source is connected. Learn how on 

“Power ON” on page 230

.

Power Button LED Status

FieldFox High Temperature Protection

The following features prevent degradation or damage in the event of high 
internal temperatures in the FieldFox.

How to monitor the internal FieldFox temperature:

— Press 

System

, then 

Service Diagnostics

.

— Then 

Internal Temperatures

.

Solid green

Power is ON

Blinking green

FieldFox in Stand By mode

Blinking amber

Battery charging

Blinking amber and green

Stand By mode and battery charging

Not lit

Power is Off and battery is not charging

Do NOT store the FieldFox in the soft-case while powered ON or in 

Standby mode.

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов