Keysight N9923A Скачать руководство пользователя страница 230

Страница: 230 / 276

230 Keysight N9923-90001 User’s Guide

System Settings
System Configuration

—

Static IP Address

- Enter the IP Address – including periods - in the

format nnn.nnn.nnn.nnn

—

Static Subnet Mask

- Enter the Subnet Mask – including periods - in the

format nnn.nnn.nnn.nnn

—

Static Gateway

- Enter the Static Gateway – including periods - in the

format nnn.nnn.nnn.nnn

—

Static DNS

- Enter the Static DNS – including periods - in the format

nnn.nnn.nnn.nnn6

—

Apply Settings

Choose from:

—

Power Up

The above settings take effect when the FieldFox is started.

—

Now

The above settings take effect immediately.

— Press

Done Edit

when finished.

Power ON

When the FieldFox is without a power source, this setting allows the FieldFox
to power ON as soon as a charged battery or the DC Adapter is inserted

without pressing the power button.

How to set Power ON

— Press

System 7

— Then

System Configuration

— Then

More

— Then

Power ON

— Then choose from the following:

—

Auto

The FieldFox will power ON when a charged battery or the DC

Adapter is inserted.

—

Manual

The FieldFox will power ON only when the power button is

pressed.

For all A.08.15 and A.09.15 FW and above, when using Static IP addresses:

— Either a valid Static Gateway is required or 0.0.0.0.
— Either a valid Static DNS is required or 0.0.0.0.

To make the LAN settings persist after power up, toggle Apply Settings to

Now then back to Power Up. You should see a message indicating that the

LAN config file was saved.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 230 / 276

Результаты поиска

Содержание N9923A

Отзывы: