Keysight N9923A Скачать руководство пользователя страница 57

Страница: 57 / 276

Keysight N9923-90001 User’s Guide

NA (Network Analyzer) Mode
NA Mode Settings

— Then

Big Readout

—

- The A or B display state is recalled. If none have been defined,

then the default display state is recalled.

—

OFF

- The B display state is visible but without the Big Marker

Readout.

— With A or B selected, then press

Edit Big Marker (A or B)

— Then edit the following display state settings:

—

Num Traces

– Choose the Multi-Trace configuration x1, x2, or x3. Only

overlayed configurations are allowed. Learn more in

“Multi-Trace

Configurations” on page 43

—

Font Size

– Choose either Big or Super Big. Super Big marker readout #3

will cover some of the measurement grid.

—

Trace Settings

- For each possible trace (1, 2, and 3) select from the

following:

—

Measurement

– S-Parameter or Receiver measurement to display.

S11

is default. Learn more in

“About S-parameters” on page 39

—

Meas Format

–

Log

is default. Learn more in

“Format” on page 46

—

Band wid th (ON)

– Marker readout for marker bandwidth search. OFF

is default. Learn how to set BW parameters in

“Searching with

Markers” on page 179

—

Big Readout

- For each marker readout (1, 2, and 3), select from the

following:

—

Marker #

- Enter a number from 1 to 6 to create the marker. 1 is

created by default.

—

Trace #

- The marker# is created on this trace. Tr1 is selected by

default. The corresponding Num Traces must first be selected. For
example, to create a marker on Trace 3, first select Num Traces = x3.

—

Format

– Format for the marker readout. Select Default to make the

marker readout format the same as the display format. Default is
selected by default.

—

Mkr Tracking

– ON: Select the parameter to track on the standard

Marker Search menu. OFF is selected by default. When set to ON,

Peak tracking is set by default. Learn about Marker Tracking in

“Marker Functions” on page 183

—

State

– Choose from Normal, Delta, or OFF. The default marker (1) is

created in Normal. Learn more in

“Marker Functions” on page 183

—

Enabled

– Turns the Big Readout of the corresponding marker ON and

OFF. The default marker (1) is set ON by default.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 57 / 276

Результаты поиска

Содержание N9923A

Отзывы: