Keysight N9923A Скачать руководство пользователя страница 192

Страница: 192 / 276

192 Keysight N9923-90001 User’s Guide

File Management
Saving and Recalling Files

Saving and Recalling Files

The FieldFox model families are:

— N991x (VNA/SA) model family

— N992x (VNA) model family

— N993x (SA) model family

— N995x (VNA/SA) model family

— N996x (SA) model family

Save Files

How to Save a File

— Press

Save/Recall 9

— Then

Save

— At the top of the current ‘labeler’ screen (see following image) check the

File Type

to save and

Device

(Internal, USB, Storage Card) to which the file

is saved. Learn how to change these settings in

“Set File Type and Select

Device” on page 196

— Then use the labeler to specify a filename.

FieldFox State files are intended to be recalled on the same instrument

model on which they were saved. Sometimes you may able to recall them

within model families. An error will result when trying to recall a state file

that was saved on a different model family.

If you are having difficulty saving to a USB flash drive, it may be a timing issue.
The turn-around time for “file open, write data, file close” to a USB drive is much
longer than to FieldFox’s internal memory. Alternative methods are

Save your content to the FieldFox’s internal memory; and then move your files
off to a USB flash drive using FTP SCPI programming. Refer to

Using FTP with

FieldFox

and to the

FieldFox Programming Guide

Save your data to the FieldFox’s internal memory, then move the data to a PC

using a binary block transfer, and delete the data from the FieldFox’s internal
memory

An example for transferring an image:

http://na.support.keysight.com/fieldfox/help/Programming/webhelp/

Examples/Transfer_Image_to_PC.htm

. Please note that the receiving

computer program needs to be able to handle the binary block transfer

See

also

FieldFox Programming Guide

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 192 / 276

Результаты поиска

Содержание N9923A

Отзывы: