Keysight N9923A Скачать руководство пользователя страница 225 | Manualshive

Страница: 225 / 276

Keysight N9923A Скачать руководство пользователя страница 225

Keysight N9923-90001 User’s Guide

225

System Settings
System Configuration

— Ant:

OK

– antenna present and working.

— Ant:

OPEN

– antenna is not drawing DC bias current. This could occur when

an active antenna is not connected properly or the antenna does not require
DC bias current. Antennas that do not require bias current can still provide

an accurate GPS reading.

— Ant:

SHORT

– antenna center pin has been shorted to ground. The internal

bias circuitry is disabled for about one minute, then re-enabled. You can
also press

GPS OFF

, then

GPS Internal

to quickly re-enable the antenna

bias.

More GPS settings

— Press

System 7

— Then

System Configuration

— Then

GPS

— Then choose from the following:

—

Sync Clock ON OFF

Enable and disable the synchronization of the FieldFox

internal clock to the GPS UTC time standard.

—

ON

The FieldFox clock is synchronized and updated approximately

every second to the time of the GPS clock.

—

OFF

The FieldFox clock is NOT synched with GPS. When set to OFF

after Sync was ON, the date and time does NOT revert back to the
settings before the clock was synchronized.

—

Lat/Lon Format

Change the format of the GPS display on the FieldFox

screen. Choose from:

—

ddd°mm’ ss.sss”

degrees, minutes, seconds (default setting)

—

ddd°mm.mmmmm’

degrees, minutes, fractional minutes

—

ddd.ddddddd°

decimal degrees

—

None

Lat/Lon is not displayed.

—

Elevation Unit

Choose from:

—

m

(Meters)

—

Feet

—

Inches

The GPS Sync setting has the same restrictions as the Date and Time

setting. Learn more in

“Date and Time” on page 218

.

«
...
223
224
225
226
227
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов