Keysight N9923A Скачать руководство пользователя страница 42

Страница: 42 / 276

42 Keysight N9923-90001 User’s Guide

NA (Network Analyzer) Mode
NA Mode Settings

——

Trans

The displayed S-parameter is converted to Z or Y

transmission, regardless of whether the S-parameter is

reflection (S11 or S22) or transmission (S21 or S12).

—1/

1/S

The displayed S-parameter is converted to 1/S-parameter.

Receiver Measurements

In NA Mode ONLY, you can make unratioed, uncorrected receiver

measurements. These measurements are typically used as diagnostic tools for
service personnel.

How to make receiver measurements

— Press

Measure 1

— Then

More

, then

Advanced

— Then choose from the following:

—

Auto

The FieldFox sets the source port based on the selected receiver.

—

Port 1

Select when measuring transmission at B receiver.

—

Port 2

Select when measuring reverse transmission at A receiver.

Learn more about Raw Receiver Measurements at the FieldFox Supplemental
Online Help:

http://na.support.keysight.com/fieldfox/help/SupHelp/FieldFox.htm

Receiver measurements are NOT corrected for absolute power. They are

only useful for making relative measurements. The Y-Axis and markers are

labeled in dB - NOT dBm. Specifically, R1 and R2, do NOT indicate the

actual power levels out of the source ports.

Port-1 test port (*1)

Port-2 test port (*2)

Port-1 reference receiver (*1)

Port-2 reference receiver (*2)

(*) indicates the Auto-selected source port for the measurement

Source Port

The FieldFox port to provide the source signal. Choose from the

following:

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 42 / 276

Результаты поиска

Содержание N9923A

Отзывы: