Keysight N9923A Скачать руководство пользователя страница 155

Страница: 155 / 276

Keysight N9923-90001 User’s Guide 155

Pulse Measurements Mode – Option 330
Pulse Measurement Settings

Marker Settings

Markers are not allowed with Meter-style measurements.

Markers are displayed on

Tr 1

and also on the zoom trace if the marker is

within the zoom window time span.

Up to six standard markers can be used to provide readouts of the Y-axis
amplitude at the current X-axis location.

The six standard markers can also be used as Delta Markers.

Learn more about standard markers in

“All about Markers” on page 174

Amplitude Markers

Amplitude markers are horizontal dotted lines that you can move to any
amplitude level on the screen. The two amplitude markers can be set

independently or used as a pair of delta markers.

Amplitude markers can be used as a visual comparison aid with the pulse

measurement traces.

How to make Amplitude Marker settings

— Press

Marker

— Then

More

— Then

Ampl Markers

— Then choose from the following:

—

OFF

Amplitude markers are NOT displayed.

—

Amplitude markers ARE displayed at their previous positions.

— Then

Ampl Mkr 1 or 2

— Enter a value in dBm for the marker using the numeric keypad, the

arrows, or the rotary knob.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 155 / 276

Результаты поиска

Содержание N9923A

Отзывы: