Keysight N9923A Скачать руководство пользователя страница 198

Страница: 198 / 276

198 Keysight N9923-90001 User’s Guide

File Management
Saving and Recalling Files

— Only data traces are saved – not memory traces.

Corrections

— When parameters are corrected, data is returned even when not displayed.

Data is returned with the correction type that is applied for each
S-parameter. The correction type for each S-parameter is annotated in the

header.

— When parameters are NOT corrected or displayed:

—With Smith chart and Polar formats, Real/Imag zero-filled data

appears as (1.0, 0.0).

—With all other formats, LogMag/Phase zero-filled data appears as (0.0,

0.0).

> Display formats

In CAT Mode, S1P files are always Magnitude (dB) / Phase (angle) format.

In NA Mode:

— Smith chart and Polar display formats are ALWAYS saved in Real/Imag data

pairs.

— All other display formats are saved in LogMag/Phase (dbAngle).

> What Data Processing functions are included in saved SNP Data:

In NA Mode, the data processing functions (such as trace math) that are
included in the SNP data depends on a Preference setting. Click

System

, then

Preferences

, then

Preferences

, then scroll to

NA, SNP File Save

, then select

from the following:

—

Default

– SNP data does NOT include smoothing. SNP data saves are taken

AFTER data processing (location 2) on the processing chain.

—

Ad vanced

– SNP data includes the following:

—With Smith or Polar display format, SNP data saves are taken BEFORE

most processing (location 1 on the data processing chain).

—With any other display format, SNP data saves are taken just AFTER

Formatting and Smoothing is applied (location 3 on the data

processing chain). For each non-active trace, SNP trace data is
reprocessed using the data processing chain of the active trace.

See the FieldFox data processing chain at the

Supplemental Online Help:

http://na.support.keysight.com/fieldfox/help/SupHelp/FieldFox.htm

Learn

more about System Preferences in

“Preferences” on page 213

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 198 / 276

Результаты поиска

Содержание N9923A

Отзывы: