Keysight N9923A Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 276

Keysight N9923A Скачать руководство пользователя страница 111

Keysight N9923-90001 User’s Guide

111

Calibration for NA, CAT, and VVM Modes

the data stored within the memory of the ECal module. The FieldFox uses this
stored data, along with the measured data, to calculate the error terms for a

measurement calibration.

You can perform the following calibrations with ECal:

— 1-Port Reflection calibration

— Full 2-Port calibration
All Keysight USB ECal modules are supported. ECal modules are available in a

variety of connector types, covering many frequency ranges. For information
about available ECal modules, see

http://www.keysight.com/find/ecal

Select an ECal module that has connectors of the same type and gender as the
DUT. If such an ECal module is not available, a module with connectors
different from the DUT can be used by selecting a User Characterization. This

selection is located on the Mechanical Cal Setup page of the CalWizard.
However, a User Characterization can NOT be PERFORMED using the
FieldFox. It must be performed using a bench top Keysight VNA, such as the

PNA or ENA. Learn more about User Characterization at the PNA Help website:

http://na.tm.keysight.com/pna/help/latest/S3_Cals/ECal_User_Characteriza

How to Perform a Calibration Using ECal

— Make measurement settings on the FieldFox (frequency range, number of

points, etc.)

— Connect the ECal module USB cable to the FieldFox USB.

— Allow the module to warm up until it indicates READY. This may take several

minutes.

— Connect the ECal module ports to the FieldFox at the calibration reference

plane (where the DUT will be connected).

— Press

Cal 5

to start the Calibration.

— Press

Mechanical Cal / ECal

— Press

Change DUT Connectors

. For each test port to be calibrated, select

the

Connector Type

and

Gender

of the DUT / ECal module. The connected

ECal module and relevant User Characterizations will appear, with the ECal
factory default as the default Cal Kit.

— Optionally press

Advanced

then

ECal Auto Orient

.

—

ON

(default) The FieldFox automatically senses the direction in which

the ECal module ports are connected to the FieldFox ports.

The frequency range of the measurement MUST be within the frequency

range of the ECal module or an error will appear when “Calculating Steps”

during the calibration.

«
...
109
110
111
112
113
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов