Keysight N9923A Скачать руководство пользователя страница 244 | Manualshive

Страница: 244 / 276

Keysight N9923A Скачать руководство пользователя страница 244

244 Keysight N9923-90001 User’s Guide

Working with the Lithium-Ion Battery
Reconditioning Battery

Reconditioning Battery

Reconditioning a battery can be performed ONLY with the External Battery

Charger (N9910X–872).

1.

Insert a battery into the left bay of the external charger.

2.

Press the button labeled Push to Recalibrate Left Battery Bay

3.

The charger will charge the battery fully, discharge it completely, then

recharge it fully again. The entire process can take up to 12 hours.

4.

Install the battery into the FieldFox.

5.

On the System, Battery screen, verify that the battery is fully charged.

Battery Care

Visually inspect the battery periodically for signs of degradation, such as
swelling, cracking of the battery shell, or leakage of fluid. If degradation

occurs, replace the battery and dispose of it properly. Refer to

Battery Disposal” on page 245

. Operation with a degraded battery could result

in damage to the FieldFox.

Maximizing Battery Life

— If AC power is not continuously available (Ex: in a field environment), use the

battery and recharge it when it holds a 20% to 50% charge, as shown on
the screen’s battery charge icon. At this charge level, 2 or 3 segments show

on the battery gauge.

— If the FieldFox is not going to be used for more than a week, remove the

battery. Best practice is to store the battery with a charge of about 50%. At
this charge level, 3 segments show on the battery gauge.

— Allow a battery to warm to room temperature before charging it.

Temperature shock can damage the battery chemistry and in some cases
cause a short circuit.

«
...
242
243
244
245
246
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов