Keysight N9923A Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 276

Keysight N9923A Скачать руководство пользователя страница 115

Keysight N9923-90001 User’s Guide

115

Calibration for NA, CAT, and VVM Modes

Definitions

:

Defined THRU

– A THRU standard for which there is a Cal Kit definition such as

in the 8551xA Cal Kits.

Flush THRU

(also known as Zero length THRU) – When the test port cables

mate together when measuring an Insertable DUT. No actual THRU standard is

required because the test port cables are directly connected. Flush THRU is
also a Defined THRU with a definition of zero loss and zero length.

Sweep Directions

– Both FULL 2-Port Cals listed below result in correction

that requires background measurements sweeps in both directions, regardless
of the displayed measurements. The displayed traces are updated at a slower

rate than Enhanced Response and 1-port calibrations, which require sweeps in
one direction only.

1-Port (OSL)

DUT: Not Applicable

S-parameters Corrected: S11 or S22

Standards: OPEN, SHORT, LOAD

Sweeps in ONE direction.

FULL 2-Port (Requires Option 122)

Most comprehensive calibration. Corrects all S-parameters

DUT: Non-Insertable or Insertable

Standards: OPEN, SHORT, LOAD on

BOTH

ports. Any THRU between ports.

For more information on the Unknown THRU process, see the FieldFox

Supplemental Online Help:

http://na.support.keysight.com/fieldfox/help/SupHelp/FieldFox.htm

Non-insertable DUT – A device whose

connectors could NOT mate together. They

either do not have the same type of connector

or they have the same gender. This also means

that the test port cables could NOT mate

together as in the above diagram.

Insertable DUT – A device whose connectors

could mate together. They have the same type

of connector and opposite or no gender. This

also means that the test port cables could

mate together, as in the above diagram.

«
...
113
114
115
116
117
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов