Keysight N9923A Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 276

Keysight N9923A Скачать руководство пользователя страница 88

88 Keysight N9923-90001 User’s Guide

CAT (Cable and Antenna Test) Mode
2-Port Insertion Loss Measurements

14.

Use Averaging to remove random noise from high-loss measurements.

Press

BW 2

then

Average

.

The displayed trace shows the Cable Loss values in one direction through the
cable. A Return Loss measurement would show the loss for both down the
cable and back. Therefore, a Cable Loss measurement is the same as a Return

Loss measurement divided by 2.

The average Cable Loss across the specified frequency range is shown on the
screen below the graticules.

2-Port Insertion Loss Measurements

A 2-port Insertion Loss measurement is used to measure the loss through a

DUT (device under test) – or cable – over a specified frequency range. The
FieldFox signal source is transmitted out the RF OUT connector, through the
DUT, and into the RF IN connector. Both ends of the DUT must be connected

to the FieldFox, either directly or indirectly using the cable used in the
normalization cal.

‘Insertion’ loss simply means

loss

through a device, usually expressed in dB. It

is exactly the same measurement as “S21 Transmission” in NA Mode.

2-port Insertion Loss measurements are generally more accurate than 1-port

Cable Loss measurements.

How to make a 2-port Insertion Loss Measurement

— Press

Mode

then

CAT

.

— Then

More

then

Insertion Loss (2-Port)

.

— Press

Freq/Dist

and enter

Start

and

Stop

frequency values of the

measurement.

— Press

Sweep 3

, then select a

Resolution

setting.

— Press

Cal 5

, then perform a calibration. Learn more on

“How to Perform a

Calibration” on page 104

.

— Connect the DUT and view the insertion loss measurement results.
When measuring very long lengths of cable, it may be necessary to increase
the sweep time. Learn how in

“Sweep Time” on page 82

. Learn why in the

Supplemental Online Help

http://na.support.keysight.com/fieldfox/help/SupHelp/FieldFox.htm

«
...
86
87
88
89
90
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов