Keysight N9923A Скачать руководство пользователя страница 131

Страница: 131 / 276

Keysight N9923-90001 User’s Guide 131

Power Meter (USB) Mode
USB Power Meter Settings

— Press

Scale / Amptd

— Then

More

— Then

Autoscale

Relative and Offset Power Measurements

Power measurements can be made that are relative to another reading or that
are offset by a fixed value.

— Use Relative to measure the difference between power levels.

— Use Offset to account for components or a long length of cable that is used

before the power sensor. For example, if using a 10 dB attenuator to protect
the FieldFox, enter an Offset Value of 10 to read the power as it would

appear without attenuation. If using a 10 dB amplifier, enter an Offset Value
of –10 to read the power as it would appear without amplification.

How to set Relative and Offset Power Measurements

— Press

Scale / Amptd

— Then choose from the following:

—

Relative Off On

When switched to ON, the FieldFox measures and

stores the current power level. Subsequent power measurements

display a power level which is relative to the stored value. When
relative is ON, the units change from dBm to dB or from Watts to %.

—

Offset Off On

Toggles ON and OFF the displayed power level using

the Offset value.

—

Offset Val

Value by which the power meter display is offset. A

positive value compensates for a component with loss. A negative
value compensates for a component with gain. Offset values are

limited to +/- 100 dB.

Display Units

Select whether to display power in dBm or Watts. When making relative power
measurements, these change to dB and %.

How to set Power Meter display units

— Press

Meas Setup 4

Scale / Amptd

More

— Then

Unit

— Then choose from the following:

—

dBm (dB)

Sets Power Meter display to dBm or dB.

—

Watt (%)

Sets Power Meter display to Watts or %.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 131 / 276

Результаты поиска

Содержание N9923A

Отзывы: