Keysight N9923A Скачать руководство пользователя страница 182

Страница: 182 / 276

182 Keysight N9923-90001 User’s Guide

Data Analysis Features
All about Markers

—

Peak Right

Moves the active marker to the next data point to the right that

meets the ‘Peak’ criteria. When no data points to the right meet the ‘Peak’

criteria, the marker does not move.

—

More

then

Min Search

(Not available in DTF) Moves the active marker to

the LOWEST amplitude data point of the trace.

The following applies to DTF Measurements ONLY:

—

More

—

Track Peaks ON OFF

When Track Peaks is ON, markers will find the new

peak with every sweep. While in this Mode, the markers can NOT be turned
OFF or moved.

—

Find 3 Peaks

Three markers are created and find the highest peaks (faults)

on the trace.

What Is a ‘Peak’

You define what the FieldFox considers a “peak” by setting the Peak

Threshold

and Peak

Excursion

These two peak criteria settings are set individually for each trace and for each

mode.

These settings do NOT survive a FieldFox or Mode Preset.

How to set Peak Criteria

— Press

Mrk ->/Tools

— In

CAT

and NA

modes:

—Then

Peak Search

— Then

Peak Criteria

— Then select the following:

—

Peak Threshold

Minimum amplitude (dB). To be considered valid, the

peak must be

above

the threshold level. The valley on either side can

be below the threshold level. Default = –190 for CAT and NA Modes;

–90 for SA Mode.

The Peak Threshold and Excursion settings are NOT available in DTF

measurements. To make these settings, create a non-DTF CAT mode

measurement, then change the measurement back to DTF.

CAT mode Loss measurements are displayed in positive values. In these

cases, the Peak Threshold setting is inverted. For example, Peak Threshold

= -20 will consider any peak that has less Loss than 20 dB to be valid.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 182 / 276

Результаты поиска

Содержание N9923A

Отзывы: