Keysight N9923A Скачать руководство пользователя страница 81

Страница: 81 / 276

Keysight N9923-90001 User’s Guide

CAT (Cable and Antenna Test) Mode
CAT Mode Settings

— Then

Average N

where

is the current count setting.

— Enter a value using the numeric keypad. Enter 1 for NO averaging.

— Press

Enter

— While Trace Averaging is in process, press

Sweep 3

then

Restart

to restart

the averaging at 1.

Smoothing

Trace smoothing averages a number of

adjacent

data points to smooth the

peak-to-peak noise values on a displayed trace. The number of adjacent data

points that are averaged is known as the smoothing aperture. Aperture is set
by specifying a percentage of the X-axis span.

Trace smoothing does NOT significantly increase measurement time.

Smoothing can be used with any CAT format.

When enabled,

Smo

appears on the FieldFox screen.

How to set Smoothing

— Press

BW 2

— Then

Smoothing ON OFF

— Then

Sm. Aperture

and enter a value between 0 and 25 (percent) using the

numeric keypad.

— Press

Enter

Single or Continuous Measure

This setting determines whether the FieldFox sweeps continuously or only once
each time the

Single

button is pressed. Use

Single

to conserve battery power

or to allow you to save or analyze a specific measurement trace.

This setting can be changed at any time without affecting calibration accuracy.

How to set Single or Continuous

— Press

Sweep 3

— Then choose one of the following:

—

Single

Automatically sets Continuous OFF and causes FieldFox to

make ONE sweep, then hold for the next Single key press.

Hold

annotated in the upper left corner of the display when NOT sweeping,

and changes to an arrow --> while the sweep occurs

—

Continuous ON OFF

Makes continuous sweeps. This is the typical

setting when battery power is not critical.

You can also use

Run / Hold +/-

to toggle between Single and Continuous.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 81 / 276

Результаты поиска

Содержание N9923A

Отзывы: