Keysight N9923A Скачать руководство пользователя страница 235

Страница: 235 / 276

Keysight N9923-90001 User’s Guide

235

System Settings
Service Diagnostics

Service Diagnostics

— The Service diagnostics menu is generally used to display service-related

information. To access these menu items, press

System 7

then

Service

Diagnostics

System Information

The System information table shows important information about your
FieldFox. The following is the most useful information:

—

Model Number

– FieldFox model

—

Serial Number

– Identification number of your FieldFox

—

Firmware Release

– The currently installed version of software. Check to

see if you have the latest firmware at:

www.keysight.com/find/fieldfoxsupport

—

Network Identity

– The network name and current IP address of your

FieldFox.

—

Reflectometer Factory Cal

- The Factory (CalReady) Calibration shows the

date and time that the factory cal was performed for each test port and the
Thru connection. The format is P1 <date time>, P2 <date time>, P1-P2

<date time>. The factory calibration is updated when you send your
FieldFox to Keysight for Instrument Calibration. Learn more in

“Instrument

Calibration” on page 265

Event Log

The Event Log shows the information that has appeared on the FieldFox

screen. The most recent information is at the top of the table.

Press Clear Events to erase this information.

Battery

Learn more in

Chapter 16, “Working with the Lithium-Ion Battery”, on page

239

Internal Temperatures

Learn about the importance of the internal FieldFox temperatures in

“FieldFox

High Temperature Protection” on page 24

Erase User Data

All data that you have written to the FieldFox can be erased with the press of a
button. You would do this if your FieldFox is located in a secure environment

and must be routinely erased of sensitive data.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 235 / 276

Результаты поиска

Содержание N9923A

Отзывы: