Keysight N9923A Скачать руководство пользователя страница 202

Страница: 202 / 276

202 Keysight N9923-90001 User’s Guide

File Management
Saving and Recalling Files

—Press

Backspace

to erase the last character from the end of the

selected keyword.

—Press

Shift

to change from upper-case to lower-case and vice versa.

—Press

Alt Keywords

to toggle through different keyword choices.

How to move the cursor:

— Use the rotary knob to move the cursor along the same row. The cursor will

change rows when it comes to a row end.

— Use the

arrows to move the cursor up and down between rows.

When the selected keyword is complete:

— Press

Done

to save all keywords and close the Edit Keywords labeler. These

keywords will exist on the FieldFox until changed.

— Press

Cancel

to close the labeler without saving changes.

Prefixes and Suffixes for Filenames

The prefix and suffix (Auto Append) can be used together to organize files.

Once set and enabled, they are automatically entered as the beginning (Prefix)
and end (Suffix - using Auto Append) of a filename when performing a Save
operation. These settings are persistent, until disabled. Refer to

“How to edit

the Prefix and Suffix (Auto Append)” on page 202

and

“How to enable/disable

Auto Append (Suffix) ” on page 204

This section contains the following sections:

—

“How to edit the Prefix and Suffix (Auto Append)” on page 202

—

“How to move the cursor” on page 194

—

“When the Prefix is complete” on page 204

—

“How to enable/disable Auto Append (Suffix) ” on page 204

How to edit the Prefix and Suffix (Auto Append)

If you want to edit a prefix on a finite set of files one time, refer to

“Manage

Files” on page 199

— Press

Save/Recall 9

— Then

More

— Then

Prefix Suffix

If you are only interested in adding a prefix or a suffix to a new file or files

one time, refer to

“Manage Files” on page 199

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 202 / 276

Результаты поиска

Содержание N9923A

Отзывы: