Keysight N9923A Скачать руководство пользователя страница 91

Страница: 91 / 276

Keysight N9923-90001 User’s Guide

DTF (Distance to Fault) Measurements
DTF Measurement Settings

DTF Measurement Settings

DTF Settings Table

You can set and view all of the DTF settings, including some calculated values,

on the DTF Settings table. Learn about the calculated values in

“Calculated

DTF values” on page 98

How to make settings on the DTF settings table

— Press

Meas Setup 4

— Then

Settings

— Press

Next Page

and

Previous Page

to view all settings.

— To change a setting:

—Use the

arrows or rotary knob to highlight a setting.

—Numeric settings can be changed by pressing numbers using the

numeric keypad. Then press Enter or select a suffix if available.

—Other settings require you to press

Edit

, then press a softkey to change

the value.

—When finished changing a value, press

Done Edit

— Press

Dock Window

to relocate the Settings table to a position relative to

the trace window. The setting persists through a Preset. Choose from the
following:

—

Full (Default setting)

Only the Settings table is shown on the screen.

The trace window is temporarily not shown.

—

Left

The Settings table is shown to the left of the trace window.

—

Bottom

The Settings table is shown below the trace window.

— When finished changing ALL settings, press

Done

to save your settings.

DTF Measurement (Format)

You can select from 3 different DTF Formats.

— Press

Measure 1

— Then choose from:

—

Distance to Fault (dB)

Faults are displayed on the Y-axis in return loss

format, expressed as a positive number in dB.

—

DTF (VSWR)

Faults are displayed on the Y-axis in SWR. Learn more

about SWR at the FieldFox Supplemental Online Help:

http://na.support.keysight.com/fieldfox/help/SupHelp/FieldFox.ht

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 91 / 276

Результаты поиска

Содержание N9923A

Отзывы: