Keysight N9923A Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 276

Keysight N9923A Скачать руководство пользователя страница 92

92 Keysight N9923-90001 User’s Guide

DTF (Distance to Fault) Measurements
DTF Measurement Settings

—

More

then

DTF (Lin)

Faults are displayed on the Y-axis in linear

(unitless) format.

DTF Start and Stop Distance

In DTF measurements, you set the physical length of cable or other device to
be tested. The FieldFox calculates the frequency range of the measurement
from this distance. The longer the cable to be tested, the lower the frequencies

that are used. You can also set the frequencies manually using the Frequency
Mode [Bandpass] setting.

How to set Start and Stop Distance

— With a DTF measurement present, press

Freq/Dist

.

— Then choose from the following:

—

Start Distance

Enter a value using the numeric keypad, the

arrows, or the rotary knob, then

Enter

. By default, the Start Distance

is set to 0 Meters. This means that the measurement will display
faults starting at the point at which calibration standards are

connected.

—

Stop Distance

Enter a value between the start distance and 5 km (or

16,404 ft.) using the numeric keypad, the

arrows, or the rotary

knob, then

Enter

.

Frequency Mode

All DTF measurements are made with frequency settings and, using Inverse
Fourier Transform (IFT), the time and distance to faults are calculated.

How to set Frequency Mode

With a DTF measurement present,

— Press

Meas Setup 4

— Then

Frequency Mode

— Choose one of the following:

—

Lowpass Mode

The frequency range of a DTF measurement is set

automatically based on the Start and Stop Distances. Use Lowpass
mode when the DUT is a cable ONLY.

The start and stop frequencies for the measurement are always annotated

on the screen below the start and stop distances.

«
...
90
91
92
93
94
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов