Keysight N9923A Скачать руководство пользователя страница 90

Страница: 90 / 276

90 Keysight N9923-90001 User’s Guide

DTF (Distance to Fault) Measurements
How to make DTF Measurements

How to make DTF Measurements

Before starting, you may need the following:

— Jumper cable or adapter to connect the beginning of the DUT to the

FieldFox.

— LOAD with correct connector type and gender to terminate the end of the

DUT (if possible).

— The known length and cable type of the DUT. If the cable type is not known,

then the Cable Loss (dB/Meter) and Velocity Factor of the DUT are required.

Connect any necessary jumper cable or adapter to the FieldFox RF OUT

port. Do NOT connect the DUT.

Press

Preset

then

Preset

to return the FieldFox to the default settings.

Then

Mode

then

CAT

Then

Distance To Fault

Press

Freq/Dist

, then

Stop Distance

and enter the length of the DUT. You

can optionally set the Start Distance

Press

Cal 5

and follow the Cal prompts. Learn all about Calibration in

“How to Perform a Calibration” on page 104

Disconnect any components or antenna that should NOT be measured and

connect a LOAD at the end of the DUT.

Press

Meas Setup 4

then

DTF Cable Specifications

Either press

Recall Coax Cable

, or directly enter the Velocity Factor/Cable

Loss of the DUT using the

Velocity Facto

r and

Cable Loss

keys.

10.

Connect the start end of the DUT to the FieldFox.

11.

Press

Meas Setup 4

then

Settings

then

Next Page

. If the

Alias-free Range

setting is False, then you may see Alias faults on the screen. Learn more

page 98

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 90 / 276

Результаты поиска

Содержание N9923A

Отзывы: