Keysight N9923A Скачать руководство пользователя страница 93

Страница: 93 / 276

Keysight N9923-90001 User’s Guide

DTF (Distance to Fault) Measurements
DTF Measurement Settings

—

Bandpass Mode

(Default setting) The frequency range of a DTF

measurement is set manually. Use Bandpass mode when the DUT

contains a diplexer or other filtering device which does not pass
some frequencies.

Typically, you will set the frequency range of the measurement to the passband

of the filter. However, you may also want to test the ability of the filter to

reject

unwanted frequencies. In this case, set the frequency range to include those
frequencies which the filter may not be adequately rejecting.

When the DTF frequencies are set manually, they may not be the optimum
frequencies for measuring the distance to fault. The distance may no longer be

alias-free. Learn more about alias-free range on

page 98

How to manually set Frequencies in Bandpass Mode

— Press

Freq/Dist

— Then

Min Start Freq

and type the start frequency to use for the DTF

measurement.

— Then

Max Stop Freq

and type the stop frequency to use for the DTF

measurement.

— OR

— Press

More

— Then

Max Freq Span

and type the frequency range to use for the DTF

measurement.

— Then

Center Frequency

and type the center frequency of the range to use

for the DTF measurement.

These settings specify the minimum and maximum frequencies to be used for
the DTF measurement. These exact frequencies may not be used, but a
narrower frequency range may be used that will still pass through the

bandpass filter.

To see the frequencies that are used in the DTF measurement, press

Meas

Setup 4

then

Settings

then

Next Page

. The calculated Start and Stop

frequencies determine the exact frequency range being used.

Coupled Frequency

When both a DTF and non-DTF measurements are present, this setting allows

you to have different frequency ranges for each measurement. Learn more in

“Coupled Frequency” on page 84

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 93 / 276

Результаты поиска

Содержание N9923A

Отзывы: