GigaDevice Semiconductor GD32A50 Series Скачать руководство пользователя

Страница: 333 / 670

GD32A50x User Manual

333

Counter center-aligned counting

In this mode, the counter counts up from 0 to the counter-reload value and then counts down

to 0 alternatively. The Timer module generates an overflow event when the counter counts to

the counter-reload value subtract 1 in the up-counting direction and generates an underflow

event when the counter counts to 1 in the down-counting direction. The counting direction bit

DIR in the TIMERx_CTL0 register is read-only and indicates the counting direction when in

the center-aligned mode.

Setting the UPG bit in the TIMERx_SWEVG register will initialize the counter value to 0 and

generate an update event irrespective of whether the counter is counting up or down in the

center-aligned counting mode.

The UPIF bit in the TIMERx_INTF register will be set to 1 either when an underflow event or

an overflow event occurs. While the CHxIF bit is associated with the value of CAM[1:0] in

TIMERx_CTL0. The details refer to

Figure 18-8. Timing chart of center-aligned counting

mode

If the UPDIS bit in the TIMERx_CTL0 register is set, the update event is disabled.

When an update event occurs, all the shadow registers (repetition counter register, counter

auto-reload register, prescaler register) are updated.

Figure 18-8. Timing chart of center-aligned counting mode

shows some examples of the

counter behavior when TIMERx_CAR=0x99. TIMERx_PSC=0x0.

Содержание GD32A50 Series































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32A50 Series

Отзывы:

Похожие инструкции для GD32A50 Series

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32A50 Series, Руководство пользователя

Результаты поиска

Содержание GD32A50 Series

Отзывы:

Похожие инструкции для GD32A50 Series

Бренды по названию

Популярные бренды