GigaDevice Semiconductor GD32A50 Series Скачать руководство пользователя | Manualshive

Страница: 27 / 670

background image

GD32A50x User Manual

27

CBUS

SBUS

DMA0

DMA1

AHB1

0

1

1

1

AHB2

0

1

1

1

As is shown above, there are several masters connected with the AHB interconnect matrix,
including CBUS, SBUS, DMA0 and DMA1. CBUS is the code bus of the Cortex®-M33 core,
which is used for any instruction fetch and data access to the Code region. Similarly, SBUS
is the system bus of the Cortex®-M33 core, which is used for instruction/vector fetches, data
loading/storing and debugging access of the system regions. The system regions include the
internal SRAM region and the Peripheral region. DMA0 and DMA1 are the buses of DMA0
and DMA1 respectively.

There are also several slaves connected with the AHB interconnect matrix, including FMC,
SRAM, AHB1, AHB2. FMC is the bus interface of the flash memory controller. SRAM is on-
chip static random access memories. AHB1 is the AHB bus connected with all of the AHB
slaves except GPIO. AHB2 is the AHB bus connected with GPIO. While APB1 and APB2 are
the two APB buses connected with all of the APB slaves.

The two APB buses connect with all the APB peripherals. APB1 is up to 50MHz, APB2
operates at full speed (up to 100MHz depending on the device).

These are interconnected using a multilayer AHB bus architecture as shown in

Figure 1-2.

Series system architecture of GD32A50x series

below:

«
...
25
26
27
28
29
...
»

Содержание GD32A50 Series































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GD32A50 Series

All in One Printer

Бренд: Baracoda Страницы: 42

Бренд: NEC Страницы: 47

Бренд: Baicells Страницы: 8

Бренд: Lab.gruppen Страницы: 35

Бренд: T&D Страницы: 122

Бренд: TC-Helicon Страницы: 2

X-Pedition 2000

Бренд: Enterasys Страницы: 86

SteelCentral AppResponse 2180

Бренд: Riverbed Страницы: 82

Бренд: Avenview Страницы: 28

Бренд: Xtreme Страницы: 83

Бренд: Vacron Страницы: 16

High-Precision AD/DA Board

Бренд: Waveshare Страницы: 8

Бренд: ETAS Страницы: 29

Бренд: Infoblox Страницы: 44

Бренд: Paradyne Страницы: 46

Бренд: Sennheiser Страницы: 22

Бренд: silicom Страницы: 16

Бренд: Sun Microsystems Страницы: 410

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды