Festo CMMP-AS-***-M0 Series Скачать руководство пользователя страница 107

Страница: 107 / 294

Setting parameters

Festo – GDCP-CMMP-M3/-M0-C-CO-EN – 1510b – English

107

Affected objects from other chapters

Index

Object

Name

Type

Chapter

607A

VAR

target_position

INT32

7.3 Positioning operating mode

607C

VAR

home_offset

INT32

7.2 Homing run

607D

VAR

software_position_limit

INT32

7.3 Positioning operating mode

607E

VAR

polarity

UINT8

5.3 Conversion factors

6093

VAR

position_factor

UINT32

5.3 Conversion factors

6094

ARRAY

velocity_encoder_factor

UINT32

5.3 Conversion factors

6096

ARRAY

acceleration_factor

UINT32

5.3 Conversion factors

6040

VAR

controlword

INT16

6.1.3 Control word (controlword)

6041

VAR

statusword

UINT16

6.1.5 Status words (statuswords)

Object 60FB

: position_control_parameter_set

The parameter set of the motor controller must be adapted for the application. The data of the position

controller must be optimally determined during commissioning using the parametrisation software.

Caution

Incorrect setting of the position regulator parameters can result in strong vibrations and

possibly destroy parts of the system!

The position controller compares the target location with the actual location and, from the difference,

creates a correction speed (object 60FA

: control_effort), which is fed to the speed regulator, taking

into account the gain and possibly the integrator.

The position controller is relatively slow, compared to the current and speed regulator. Therefore, the

controller works internally with activation, so the stabilisation work for the position controller is minim

ised and the controller can rapidly stabilise.

A proportional link normally suffices as position controller. Amplification of the position controller must

be multiplied by 256. With an amplification of 1.5 in the “Current Regulator” menu of the parametrisa

tion software, the value 384 must be written in the object position_control_gain.

The position controller normally does not need an integrator. Then the value zero must be written into

the object position_control_time . Otherwise, the time constant of the position controller must be con

verted into microseconds. With a time of 4.0 milliseconds, the corresponding value 4000 is entered in

the object position_control_time.

Since the position controller already converts the smallest position deviations into appreciable correc

tion speeds, in the case of a brief disturbance (e.g. brief jamming of the system) it would lead to very

major stabilisation processes with very large correction speeds. This can be avoided if the output of the

position controller is sensibly limited via the object position_control_v_max (e.g. 500 min

-1

The size of a position deviation up to which the position controller will not intervene (dead area) can be

defined with the object position_error_tolerance_window. This can be used for stabilisation, such as

when there is play in the system.

Содержание CMMP-AS-***-M0 Series







































































































































































































































































































Результаты поиска

Содержание CMMP-AS-***-M0 Series

Отзывы:

Бренды по названию

Популярные бренды

Festo CMMP-AS-***-M0 Series, Руководство пользователя

Результаты поиска

Содержание CMMP-AS-***-M0 Series

Отзывы:

Бренды по названию

Популярные бренды