manualshive.com logo in svg

Festo CMMP-AS-***-M0 Series, Руководство пользователя

Поделиться
Скачать
Festo CMMP-AS-***-M0 Series Скачать руководство пользователя страница 16

2

CANopen [X4]

16

Festo – GDCP-CMMP-M3/-M0-C-CO-EN – 1510b – English

2.4

Configuration of CANopen participants on the CMMP-AS-...-M0

M0

This section is only applicable for the motor controller CMMP-AS-…

-M0

.

Several steps are required in order to produce an operational CANopen interface. Some of these set­

tings should or must be carried out before the CANopen communication is activated. This section

provides an overview of the steps required by the slave for parameterisation and configuration.

Instructions on commissioning with the Festo Configuration Tool can be found in the Help

for the device-specific FCT plug-in.

When designing the CANopen interface, the user must therefore make these determinations. Only then

should parameterisation of the fieldbus connection take place on both pages. We recommend that

parameterisation of the slave should be executed first. Then the master should be configured.

The CAN-bus-specific parameters can be set on two paths. These paths are separated from one another

and are accessed via the option “Fieldbus parameterisation via DINs” on the “Application data” page in

the FCT.

The option “Fieldbus parameterisation via DINs” is active on delivery and after a reset to the factory

settings. Parameterisation with FCT for activation of the CAN bus is thus not absolutely necessary.

The following parameters can be set via the DINs or FCT:

Parameters

Setting via

DIN

FCT

Node number

0 … 3 

1)

“Fieldbus” page, operating parameters.

Activation of the CAN bus is performed automatically by

FCT (dependent on device control):

–

Device control by FCT 

}

 CAN deactivated

–

Device control released 

}

 CAN activated

Transmission rate (bit rate)

12, 13 

1)

Input/activation

8

Protocol (data profile)

9 

2)

1)

Only transferred in the event of inactive CAN communication

2)

Only transferred after a device RESET

Tab. 2.6

Overview of settings for CAN parameters via DINs or FCT

Содержание CMMP-AS-***-M0 Series







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды