Festo CMMP-AS-***-M0 Series Скачать руководство пользователя страница 192

Страница: 192 / 294

Operating modes

192

Festo – GDCP-CMMP-M3/-M0-C-CO-EN – 1510b – English

In Fig. 7.6, a new positioning task is already started while the previous one is still in process. The host

already passes the subsequent target on to the motor controller when the motor controller signals with

deletion of the bit set_point_acknowledge that it has read the buffer and started the related position

ing. In this way, positioning tasks follow each other seamlessly. For this operating mode, the object

end_velocity should be written over with the same value as the object profile_velocity so that the

motor controller does not briefly brake to zero each time between the individual positioning tasks.

Time

Velocity

Fig. 7.6

Continuous sequence of positioning tasks

If besides the bit new_set_pointthe bit change_set_immediately is also set to “1” in the controlword,

the host instructs the motor controller to start the new positioning task immediately. In this case, a

positioning task already in process is interrupted.

Содержание CMMP-AS-***-M0 Series







































































































































































































































































































Результаты поиска

Содержание CMMP-AS-***-M0 Series

Отзывы:

Бренды по названию

Популярные бренды

Festo CMMP-AS-***-M0 Series, Руководство пользователя

Результаты поиска

Содержание CMMP-AS-***-M0 Series

Отзывы:

Бренды по названию

Популярные бренды