Festo CMMP-AS-***-M0 Series Скачать руководство пользователя страница 50

Страница: 50 / 294

EtherCAT interface

Festo – GDCP-CMMP-M3/-M0-C-CO-EN – 1510b – English

4.5

Configuration of EtherCAT participants

Several steps are required in order to produce an operational EtherCAT interface. This section provides

an overview of the steps required for parameterisation and configuration of the slave.

Note: Parameterisation and commissioning of the motor controller with the EtherCAT

control interface is possible only with the connected master.

Notes on commissioning with the Festo Configuration Tool can be found in the Help for

the device-specific FCT plug-in.

When designing the EtherCAT interface, the user must therefore make these determinations. Only then

should parameterisation of the fieldbus connection take place on both pages. We recommend that the

slave parameters should be set first. The master should be configured thereafter. With correct para

meterisation, the application is ready immediately without communication faults.

We recommend the following procedure:

1. Activation of the bus communication.

EtherCAT communication is automatically started through the CMMP-AS-..-M3 if it detects after

switch-on that an EtherCAT interface is plugged in.

Communication cannot be deactivated by flipping DIL switch 8.

2. Parameterisation and commissioning with the Festo Configuration Tool (FCT).

In addition, the following settings on the fieldbus page:

–

physical units of measure (Factor Group tab)

Observe that the parameterisation of the EtherCAT function only remains intact after a

reset if the parameter set of the motor controller was saved.

3. Configuration of the EtherCAT master

following sections.

4.5.1

Setting of the physical units of measure (Factor Group)

In order for a fieldbus master to exchange position, speed and acceleration data in physical units (e.g.

mm, mm/s, mm/s

) with the motor controller, it must be parameterised via the factor group

section

5.3.

Parameterisation can be carried out via either FCT or the fieldbus.

Содержание CMMP-AS-***-M0 Series







































































































































































































































































































Результаты поиска

Содержание CMMP-AS-***-M0 Series

Отзывы:

Бренды по названию

Популярные бренды

Festo CMMP-AS-***-M0 Series, Руководство пользователя

Результаты поиска

Содержание CMMP-AS-***-M0 Series

Отзывы:

Бренды по названию

Популярные бренды