manualshive.com logo in svg

Festo CMMP-AS-***-M0 Series, Руководство пользователя

Поделиться
Скачать
Festo CMMP-AS-***-M0 Series Скачать руководство пользователя страница 80

5

Setting parameters

80

Festo – GDCP-CMMP-M3/-M0-C-CO-EN – 1510b – English

5.3

Conversion factors (factor group)

Overview

Motor controllers are used in a number of applications: as direct drive, with following gear, for linear

drive, etc. To permit easy parametrisation, the motor controller can be parametrised with the help of

the factor group so that the user can specify or read out all variables, such as speed, directly in the

desired units at the output (e.g. with a linear axis position value in millimetres and speeds in milli­

metres per second). The motor controller then uses the factor group to calculate the entries in its

internal units of measurement. For each physical variable, (position, speed and acceleration), there is a

conversion factor available to adapt the user units to the own application. The units set through the

factor group are generally designated position_units, speed_units or acceleration_units. The following

sketch illustrates the function of the factor group:

Position Factor

Item

Factor group

User units

Internal controller
units

Position units

Velocity units

±1

position_polarity_flag

Acceleration units

±1

Velocity factor

Speed

±1

velocity_polarity_flag

±1

Acceleration factor

Acceleration

Increments (Inc.)

1Revolution

4096 min

1Revolution

ń

min

256 sec

Fig. 5.2

Factor group

All parameters are stored in the motor controller in its internal units and only converted with the help of

the factor group when being written in or read out.

For that reason, the factor group should be set before the first parameter setting and not changed dur­

ing parameter setting.

The factor group is set to the following units by default:

 Size

Measurement file

Unit

Explanation

Length

Position units

Increments

65536 increments per revolution

Speed

Velocity units

min

-1

Revolutions per minute

Acceleration

Acceleration units

(min

-1

)/s

Rotational speed increase per second

Tab. 5.3

Factor group default settings

Содержание CMMP-AS-***-M0 Series







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды