Canon Vizcam 1000 Скачать руководство пользователя

Страница: 582 / 840

7-146

7. TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS

Delivery Vertical Path, Duplexing Reversing Assembly, and Holding
Tray Front Feeding Assembly

Cause

Delivery paper
deflecting
plate

Delivery
vertical path
roller

Vertical path 1
sensor,
Vertical path 2
sensor

Inlet roller

Feeding roller,
Outlet roller

Duplexing unit
reversal
sensor

Feeding drive
assembly

Duplexing
paper deflect-
ing plate

Holding tray
front feeding
sensor 1, 2

Step

Yes/No

YES

Action

Check the delivery paper
deflecting solenoid
(SL14).

Check the waste toner
feeding motor drive
assembly; if normal,
check the reversal drive
clutch (CL16).

Check the lever and the
wiring; if normal, replace
the sensor.

Check the duplexing unit
reversing motor drive
assembly.

Check the waste toner
feeding motor drive
assembly; if normal,
check the reversal drive
clutch (CL16).

Check the lever and the
wiring; if normal, replace
the sensor.

Check the duplexing
feeding motor drive
assembly.

Check the duplexing
paper deflecting plate
solenoid (SL11).

Check the guide plates
and the duplexing unit
feeding assembly for
foreign matter and defor-
mation.

Check the lever and the
wiring; if normal, replace
the sensor.

Delivery vertical path assembly

Holding tray pre-feeding assembly

Duplexing unit reversing assembly

Checks

Does the delivery paper deflecting
plate operate normally?

Does the delivery vertical path roller
operate normally?

Does each sensor operate normally?

Does the inlet roller operate nor-
mally?

Does the feeding/outlet roller operate
normally?

Does the duplexing unit reversal
sensor operate normally?

Does the feeding assembly operate
normally?

Is the duplexing paper deflecting
plate operating normally?

Does the holding tray front feeding
sensor (PS8, PS9) operate normally?

Содержание Vizcam 1000







































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Vizcam 1000

Отзывы:

Похожие инструкции для Vizcam 1000

Бренды по названию

Популярные бренды

Canon Vizcam 1000, Руководство по обслуживанию

Результаты поиска

Содержание Vizcam 1000

Отзывы:

Похожие инструкции для Vizcam 1000

Бренды по названию

Популярные бренды