Canon Vizcam 1000 Скачать руководство пользователя | Manualshive

Страница: 184 / 840

background image

3. OPERATION AND TIMING

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)

3-140

c.

Lifter Operation
Figure 3-610 shows an outline of multifeeder lifter operation.
When the Start key is pressed, the multifeeder lifter motor (M1) rotates clockwise to raise the multifeeder

lifter by the lifter plate until the multifeeder lifter sensor (upper: PS2) turns ON.

This ascending movement of the lifter puts the paper on the multifeeder tray in contact with the

multifeeder pick-up roller, making it ready for pick-up.

The multifeeder motor rotates in reverse at the following timing so that the multifeeder lifter lowers until

the multifeeder lifter sensor (lower: PS3) turns ON.

• When paper is absent (for supply of paper).
• When a jam has occurred (for jam removal).
• When copying ends (for supply of paper or making changes).
If the multifeeder lifter sensor (PS2, PS3) does not turn ON within a specific period of time, ‘E040’ will be

indicated on the control panel.

Figure 3-610

DC controller PCB

M1

Multifeeder lifter sensor
(upper: PS2)

Multifeeder
lifter motor

Multifeeder lifter
sensor (lower: PS3)

Multifeeder lifter

Paper

Multifeeder
pick-up rollers

Multifeeder lifter motor drive signal (M1CW/M1CCW)

Multifeeder lifter detection (upper)

signal (PS2DT)

Multifeeder lifter detection (lower)

signal (PS3DT)

Multifeeder relay PCB

Sensor lever

Sensor lever

Slide guide

Front

Lifter

J2207B
-5

J2207B
-13

J2209B
-10,-11

«
...
182
183
184
185
186
...
»

Содержание Vizcam 1000









































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vizcam 1000

Бренд: Hitachi Страницы: 176

Бренд: Kyocera Страницы: 160

IMAGERUNNER 2016

Бренд: Canon Страницы: 2

Бренд: Xerox Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды