Canon Vizcam 1000 Скачать руководство пользователя

Страница: 466 / 840

7-30

7. TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS

Orientation of the Feeding
Roller 2 (duplexing unit pick-
up assembly)

When installing the feeding roller 2 [1], make

sure that the round marking [2] is to the front.

Color of the coller : Front ---- gold

Rear ----- silver

[2]

[1]

Collar

Green

(rubber portion)

Front

Figure 7-253

Adjusting the Pressure of the
Separation Roller (cassette
pick-up assembly/duplexing
unit pick-up assembly)

If double-feeding or pick-up faults occur during

pick-up operation, change the position of the pres-
sure spring of the separation roller.
a. If double-feeding occurs, move the spring in

the direction of A. (decrease the pressure)

b. If pick-up faults occur, move the position of the

spring in the direction of B. (increase the pres-
sure)

[1]

[4]

[2]

[3]

[1] Feeding roller

[3] Locking lever

[2] Separation roller

[4] Pressure spring

Figure 7-254

Adjusting the Position of the
Cassette Pick-Up Roller Re-
leasing Solenoid (SL9, SL10)

Install the solenoid so that the pick-up roller arm

[1] butts against the upper stay [2] when the
plunger of the solenoid is pushed in.

Butted.

[2]

[1]

Figure 7-255

Содержание Vizcam 1000







































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Vizcam 1000

Отзывы:

Похожие инструкции для Vizcam 1000

Бренды по названию

Популярные бренды

Canon Vizcam 1000, Руководство по обслуживанию

Результаты поиска

Содержание Vizcam 1000

Отзывы:

Похожие инструкции для Vizcam 1000

Бренды по названию

Популярные бренды