manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 63 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 63

61

ENGINE MANAGEMENT MODULE (EMM)

DIAGNOSTIC SOFTWARE FUNCTIONS

4

Ignition Test

Use the diagnostics software to test each ignition
circuit. Refer to 

Static Ignition Test

 on p. 75.

Fuel Test

Use the diagnostics software to test each fuel
injector circuit. Refer to 

Fuel Injector Static Test

on p. 78.

Oil Injector

Use the diagnostics software to test the oil injec-
tion pump circuit. Refer to 

OILING SYSTEM

TESTS

 on p. 151.

Fuel Pump

Use the diagnostics software to test the fuel pump
circuit. Refer to 

Fuel Pump Static Test

 on p. 78.

Tachometer

This test is used to check operation of the tachom-
eter circuit.

Dynamic Tests

Dynamic tests are performed with the outboard
running.

Ignition Test

This test momentarily disables the ignition and
fuel injection circuits to one cylinder. By dropping
one cylinder, RPM and running quality changes
can be observed. Refer to 

DYNAMIC TESTS

 on

p. 70.

Fuel Test

This test momentarily disables one fuel injector
circuit. By dropping one cylinder, RPM and run-
ning quality changes can be observed. Refer to

DYNAMIC TESTS

 on p. 70.

Prime Oil

This test is used to cycle the oil injection pump for
priming the oiling system. Perform this test with
outboard running to activate oil injection pump.

Dynamic Tests Screen

008141

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов