BRP Evinrude E-TEC Series Скачать руководство пользователя страница 254

Страница: 254 / 342

252

GEARCASE

WATER PUMP SERVICE

Sharp edge of the key is leading edge during
driveshaft rotation. Slide the impeller housing
down the driveshaft. Engage the impeller with the
key.

Make sure the impeller engages the

impeller key. Serious powerhead damage will
result if impeller key is not in place.

Lightly coat both sides of a new impeller plate
gasket with

Gasket Sealing Compound.

Place

gasket on the gearcase.

Place the impeller plate over the gasket.

Slide the driveshaft down into the gearcase and
engage the pinion.

Turn the driveshaft until holes of the impeller
housing are aligned with holes of the gearcase.
Apply

Gasket Sealing Compound

to threads of the

impeller housing screws. Tighten the screws to a
torque of 60 to 84 in. lbs. (7 to 9.5 N·m).

Apply

Adhesive 847

to outside of water tube

grommet. Install grommet and locate grommet
bosses into holes of impeller housing.

Driveshaft rotation

Drive key

CO2995

NOTICE

007663

Grommet

007664

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 254 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: