manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 23 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 23

21

ROUTINE SERVICE

BATTERY AND BATTERY CONNECTIONS

2

BATTERY AND BATTERY 
CONNECTIONS

Check battery connections frequently. Periodically
remove battery to clean and service connections.

•

Confirm that battery meets the minimum engine
requirements.

•

Connections must be clean and tight.

•

Observe all wiring connections prior to disas-
sembly.

Disconnect battery negative (–) cable 

first

 and the

battery positive (+) cable last.

Clean all terminals, battery posts, and connectors
with a solution of baking soda and water. Use a
wire brush or battery terminal tool to remove cor-
rosion buildup. Rinse and clean all surfaces.

IMPORTANT:

Connect the battery positive (+)

cable to the battery positive (+) post FIRST. Con-
nect the battery negative (–) cable to the battery
negative (–) post LAST.

Install a starwasher on the threaded battery post.
Stack cables from the outboard, then cables from
accessories. Finish this connection with a hex nut.

Do not use wing nuts to fasten ANY

battery cables. Wing nuts can loosen and
cause electrical system damage not covered
under warranty.

Tighten all connections securely. Apply 

Triple-

Guard

 grease to prevent corrosion.

WARNING

Keep the battery connections clean, tight,
and insulated to prevent their shorting or
arcing and causing an explosion. If the bat-
tery mounting system does not cover the
connections, install protective covers.
Check often to see that connections stay
clean and tight.

Marine Style Battery Post
1.

Starwasher

2.

Hex nut

3.

Terminal Insulator

DR5103

WARNING

Battery electrolyte is acidic—handle with
care. If electrolyte contacts any part of the
body, immediately flush with water and
seek medical attention.

3

2

1

NOTICE

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов