BRP Evinrude E-TEC Series Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 342

BRP Evinrude E-TEC Series Скачать руководство пользователя страница 94

92

ELECTRICAL AND IGNITION

CHARGING SYSTEM TESTS

12 V Charging Circuit

To test the operation of the regulator in the battery
charge module, you must be able to run the out-
board continuously at approximately 5000 RPM,
such as in a test tank or on a marine dynamome-
ter.

The test consists of monitoring the system’s
response to a partially discharged battery. Use a
variable load tester to discharge the battery.

Disconnect the battery cables at the battery.

Use an inductive amp meter or connect a 0 to
50 A ammeter in series between the red wire of
engine wire harness (alternator output from Bat-
tery Charge Module)

and the positive (B+) battery

cable terminal of starter solenoid.

Fluke

†

model 334 or 336,

Snap-On

†

model MT110

or EETA501, and various other amp meters
should be available through local tool suppliers.

Reconnect the battery cables.

Following the manufacturer’s directions, connect
the variable load tester (carbon pile) across the
battery terminals.

Stevens

model LB-85 and

Snap-On

model MT540D are examples of testers

available.

WARNING

Excessive battery discharge rates might
overheat battery causing electrolyte gas-
sing. This might create an explosive atmo-
sphere. Always work in a well ventilated
area.

Variable Load Test Diagram
1.

Red wire (alternator output from

EMM

)

2.

Starter solenoid

3.

Battery cable terminal (B+)

4.

Variable load tester

5.

Ammeter

002077

Battery Charging Graph

007352

2

1

5

4

3

Battery Charging

«
...
92
93
94
95
96
...
»

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов