manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 140 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 140

138

FUEL SYSTEM

FUEL COMPONENT SERVICING

Reconnect circulation fuel pump electrical con-
nector.

I

Reinstall the oil tank. Refer to 

Oil Tank Assembly

on p. 155.

Reconnect the battery cables at the battery.

Reconnect fuel hose connector to outboard.

IMPORTANT:

Install injector service data (3.5

in. floppy disk) by using the Injector Replacement
Utility of 

Evinrude Diagnostics

 software. Check

the 

Injector Coefficients

 screen to make sure that

all injectors are positioned properly.

Squeeze primer bulb to prime fuel system. Hold
pressure on bulb and observe for fuel leaks.

Use static test screen of 

Evinrude Diagnostics

software to run fuel pump. Observe for fuel leaks.

Run outboard and check for fuel leaks.

IMPORTANT:

Pay close attention to fuel vapor

separator / fuel injector connection for leaks.

Repair any leaks before returning outboard to ser-
vice.

Intake Manifold Service

Removal

Disconnect vapor separator vent hose, main bear-
ing vent hose, air temperature sensor, crankshaft
position sensor, and throttle position sensor. 

Use Ball Socket Remover Tool, P/N 342226, to
remove throttle link arm.

Remove throttle body screws and throttle body
assembly.

Remove gasket from throttle body.

Remove screws and reed plate assembly from the
crankcase.

1.

Protective cap

2.

Fuel injector electrical connectors 

3.

Circulation fuel pump electrical connector

007105

1

2

3

1.

Link arm

2.

Throttle body screws

007426

1.

Screws

007427

2

1

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов