BRP Evinrude E-TEC Series Скачать руководство пользователя страница 68

Страница: 68 / 342

ENGINE MANAGEMENT MODULE (EMM)

EMM SERVICING

EMM SERVICING

IMPORTANT:

If a new

EMM

is being installed,

refer to

EMM Transfer

on p. 65.

Removal

Disconnect cooling hoses from

EMM

Disconnect J1-A connector.

Remove two

EMM

retaining screws. Remove

EMM

Installation

Installation is the reverse of removal. Pay close
attention when performing the following tasks.

Make sure isolator mount is in place on recoil
starter housing. Slide pin at rear

EMM

into posi-

tion on isolator mount.

IMPORTANT:

Turn self-tapping screws counter

clock-wise to start the threads and clockwise to
tighten. Failure to follow this procedure can dam-
age the threads of the housing.

Tighten screws securely.

Install harness connector and cooling hoses.
Secure hoses with tie straps.

Cooling hose connections

EMM

mounting screws

007396

Isolator mount

Pin

007397

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 68 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: