BRP Evinrude E-TEC Series Скачать руководство пользователя страница 176

Страница: 176 / 342

174

POWERHEAD

POWERHEAD DISASSEMBLY

Remove crankcase flange screws. Loosen

stages

and remove the main bearing screws.

Separate crankcase and cylinder block. It may be
necessary to tap on crankshaft with a rawhide or
rubber mallet to loosen.

Crankshaft Assembly Removal

Carefully lift crankshaft straight up and remove
from crankcase.

Connecting Rods and Pistons

Use an appropriate ring expander to remove all
piston rings from pistons. Discard the rings.

Remove wrist pin retaining rings. Discard retaining
rings.

The wrist pin fit is loose on both sides. Push the
wrist pin through to free the piston from the con-

Flange screws

Main bearing screws

007748

007749

007750

WARNING

Wear safety glasses to avoid injury.

007751

007752

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 176 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: