BRP Evinrude E-TEC Series Скачать руководство пользователя страница 301

Страница: 301 / 342

S–11

SAFETY

Outboard Mounting System and Safety

What could happen?

How Can Loss of Mounting Be Minimized?
•

Read

understand

, and

follow

manufacturer’s

instructions.

•

Follow warnings marked “

” closely.

What is most important?

•

Outboard must

stay

in position on boat’s transom.

Outboard may

S...L...I...D...E on transom

Boat may turn and be hard
to steer.

Outboard may

T...I...L...T on transom

Boat may turn and be
hard to steer.

•

If outboard hits something solid and does not stay on
the transom, boat occupants may be injured from the
outboard or its parts entering the boat.

Boat’s transom could break away.

Outboard may be lost overboard.
Boat may

SINK

The mounting system includes:

•

outboard parts

•

bolts, nuts, and washers

•

boat’s transom

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 301 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: