BRP Evinrude E-TEC Series Скачать руководство пользователя страница 167

Страница: 167 / 342

165

COOLING SYSTEM

THERMOSTAT AND PRESSURE RELIEF VALVE SERVICING

Remove spring, thermostat, and gasket.

Inspection

Inspect all parts for cracks, heat damage, or signs
of corrosion. Replace damaged parts. Clean
debris from housing and parts.

Assembly

Assembly is the reverse of disassembly. Pay
close attention when performing the following

additional

tasks.

Install a

new

plunger seal on plunger.

Apply a light coat of

Gasket Sealing Compound

new

o-ring and place in groove in plate.

Install thermostat gasket, thermostat and spring
into thermostat housing.

Install pressure valve assembly into housing.

Apply

Nut Lock

to screw threads. Tighten screws

to a torque of 84 to 106 in. lbs. (9.5 to 12 N·m).

Spring, thermostat and gasket

007378

007379

Pressure Relief Valve Assembly Components

007380

Plunger seal

Plate o-ring

007381

Содержание Evinrude E-TEC Series























































































































































































































































































































































Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы:

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 167 / 342

Результаты поиска

Содержание Evinrude E-TEC Series

Отзывы: