manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 228 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 228

226

MIDSECTION

STERN BRACKET – MANUAL TILT MODELS

Align dowel pin and steering friction lever as
shown.

Install locking nut. Temporarily tighten locking nut
three to four full turns. Final adjustment will be
performed later.

Lubricate the swivel bracket through the four lubri-
cation fittings with 

Triple-Guard

 grease.

Apply 

Triple-Guard

 grease to both sides of thrust

washer. Install thrust washer on steering arm.

Install lower mount bracket on steering arm.

Install lower mount retaining screws. Tighten
screws to a torque of 10 to 12 ft. lbs. (14.5 to 16.5
N·m).

Install exhaust housing. Refer to 

EXHAUST

HOUSING SERVICE

 on p. 203.

Install tiller handle. Refer to 

TILLER HANDLE

SERVICE

 on p. 227.

Adjust tiller steering friction. Refer to 

Steering

Friction Adjustment

 on p. 24.

5.

Dowel pin

6.

Steering friction lever

007458

1.

Steering friction nut

007684

1

2

1

1.

Thrust washer

007624

1.

Retaining screws

007582

1

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов